Industrial Adhesive Sealant Polymer Silicone Apply For Weld Seam Sealing
7931(HT9301MS) MS sealant ,silicon alkyl terminated polyether, sealing of joints, such as weld seam sealing MS sealant is a silicon alkyl (silicone sealant, industry sealant, industry silicone)terminated polyether as a main component, low viscosity, and general type of one component moisture...
|Name:||7931 MS Sealant||Density (g/cm3):||1.47|
|Tack Free Time:||40||Pressure Flow Viscosity:||6|
|Room Temperature Vulcanized Depth (mm/24h):||2.8||Tensile Strength:||1.5|
|Elongation At Break:||350||Hardness:||40|
7931(HT9301MS) MS sealant ,silicon alkyl terminated polyether, sealing of joints, such as weld seam sealing
MS sealant is a silicon alkyl (silicone sealant, industry sealant, industry silicone)terminated polyether as a main component, low viscosity, and general type of one component moisture curable sealant. Curing material combines the advantages of polyurethane and silicone adhesive sealant products, is a new generation of. The operating period is long, low modulus, without bottom coating, curing, paintable with high elasticity, resistance to ultraviolet light and excellent weather ability. Free of solvent, isocyanine free, non silicone, products tasteless environmental protection.
Long operating period, there is preliminary fixed the sealing of joints, such as weld seam sealing.
Characteristics before curing
Typical values range
Color white / Black / grey paste
The base material chemical composition: Silane modified polyether
Density (g/cm3) (GB/T13354-1992)1.47 1.35-1.55
Tack free time (min) 40 10-60
Pressure flow viscosity(s/10g) 6 5-15
Characteristics after curing
|Room temperature vulcanized depth (mm/24h) 2.8|
|Tensile strength(MPa) 1.5 (GB/T528-1998)||≥0.8|
elongation at break (%) 350
Hardness(shore A) 40
|Short use temperature(℃) 120|
Instructions for using
Clean:Clean the surface: remove the rust, dust and oil etc...
Dispense: The nozzle sleeve cut, take the glue mouth, cut into appropriate slope, using squeeze can glue gun is coated onto the construction site; pneumatic pressure recommended that no more than 0.4MPa sizing.
Curing:The parts are arranged in the air sizing, when after the formation of epidermis, from the surface to the interior of a room temperature curing, and 55% relative humidity at 24 hours, the curing depth of 2 ~ 4mm. With the extension of time, the curing depth increases gradually. The 7 day curing depth 6mm.
Storage: Unused plastic blocks should be tightened immediately, to seal the tube mouth save. Again, if sealed, a little crust, remove immediately after, does not affect the normal use. In the process of storage, the nozzle may also appear a few crusts, remove after normal use, does not affect the product performance.
Keep away from children.
If you accidentally come in contact with the skin, wipe in the curing a cloth before class, and using alcohol solvent scrubbing.
If the case of contact with eyes, rinse immediately with water, and medical treatment.
Recommended for use in a well ventilated place
Product safety data please refer to the product MSDS.
White: 310ml/Tube, 10tube/box, 30tube/carton
White: 600ml/ Sausage,20tube/carton
Black: 310ml/Tube, 10tube/box, 30tube/carton
Black: 600ml/ Sausage,20tube/carton
Grey: 310ml/Tube, 10tube/box, 30tube/carton
Grey: 600ml/ Sausage,20tube/carton
The industry sealant/ industry glue, as one special adhesive silicone, need to be stored in cool and dry place 8-28 degree.
600ml/ Sausage 9months